Warping, Splitting And Bowing.
Thickness: 1-3/8” or 1-3/4” Available designs: Standard 1-3/4” door – STC 31 . Hardware Options: All machining available . Glazing Options: Any panel can be replaced with glass . Recycled Content: Louvered closet doors ... Fetch Content
CLOSET ROD And ACCESSORIES - Outwater Hardware
Dimensions: .083" Wall thickness x Diameter Specified Material: Steel Finish: Polished Chrome apart to accommodate a standard 32mm boring pattern. When the door is closed, ... Return Doc
Grade 1 Cylindrical Locks
Lip to center standard Door Thickness, field adjustable Field adjustable for 1-3/8" - 2" (35mm – 51mm) thick door Storeroom or Closet Lock – Dead locking latch bolt operated by key in outside lever, or by operating inside lever. ... Access Doc
Stanley Architectural Hardware Catalog - Sliding & Folding ...
Door Thickness 13/8" 35 13/4" 44 2" 51 Door height = 2 5/8” less than finished opening height Complete Packaged Sets Installation Detail Sizing Information For installation of 2 bypassing doors, with 13/8” to 13/4” thick panels ... View This Document
Closet F75 • Latchbolt by knob either side. Deadlocking feature standard, preventing manipulation when door is closed. To order optional latchbolt with lockset, Door Thickness Specify 1-1/4"(32mm) - 1-3/4" (44mm) (standard) Backset ... Get Content Here
• KNOBSETS HEAVY DUTY CYLINDRICAL ILOCKSETS- STANDARD DUTY ...
• Door Thickness - 13/4"-2" • Backset -2 3/4" • Backset - 2'3/4" CRCL3355 I 412.00 1 422.00 STANDARD DUTY GRADE 2 LEVER LOCKSETS " Passage or Closet 2020 - Privacy 2022 - Store Door 2030 - Privacy Bedroom or Bathroom 2048 ... Doc Viewer
standard 2-3/8” optional Door Thickness 1 3 Passage/Hall/Closet: Both levers always free. Privacy/Bed/Bath: Both levers locked or unlocked by turnbutton inside. Outside lever unlocked by emergency key. Keyed Entry Lever: Both sides ... Fetch Full Source
American National Standard
DOOR DOOR THICKNESS WEIGHT 3/4" 1 1/8" 1 3/8" 1 3/4" Up To 50# 1166 118F (C) 1138 American National Standard ANSI# Door Wt. Johnson Series Number Page D8611 50 lb. Doors 200FD, 9000 Closet Rod System Order No. PKG. BULK 9018-30P 10.24 7.31 ... Doc Viewer
(Hall & Closet) PK.PAPR Remember Baldwin for door thickness. 3 midnight (east coast standard), 7 days a week. 10. 4 Door Preparation (If Needed) 3 Fold hole template along door edge with face bore center point 40" from floor. Tape template to door. Use ... Doc Retrieval
SECURITY DOOR CONTROLS
Mark the door for the end of the strike closet to Locate center line of door thickness on the jamb and attach adhesive cutout template to jamb, lining up the the top of the Red pilot lamp standard to indicate door locked. FOR 1190A ONLY: ... View Document
Baldwin will utilize standard ground transportation unless otherwise indicated. 01 Passage or Closet Function 04 Classroom, Entrance or Office Function 8 = 3.50” door thickness 2.75” Backset 2.50” Backset 1 for RLS 5 for RLS ... Read Full Source
BANDIT Active Security
Rubber supports, a 50 mm extended ejection nozzle (a standard closet door has a thickness of approximately 20 mm) and a heat resistant black metal door rosette (ejection nozzle passage). This way you can hide the device and at the outside only a ... Read Full Source
Door Prep Cross Bore 2 1/8”. Door Thickness 1 3/8” – 1 3/4” standard 200 Passage/Hall/Closet: Both levers always free. 300 Privacy/Bed/Bath: Both levers locked or unlocked by turnbutton inside. Outside lever unlocked by emergency key. ... Document Retrieval
Wardrobe Sliding doors
A variety of standard and decorator colour ranges are available in most locations. Over 10mm Timber sill board thickness to suit Also note that not all sliding door panel infills are available in all sizes and in all branches. signature wardrobe doors ... View Doc
4910.1 TABLE OF CONTENTS CHAPTER 5 MATERIALS
Complies with the applicable standard. b. Each steel sliding glass door unit shall bear a label that identifies the manufacturer, Closet doors may be 1-1/8 in thick, The thickness of resilient flooring may be less than ... Retrieve Document
SLIDING DOOR SYSTEM S34 BI-FOLD PRODUCT LIST
_ Maximum glass thickness 8mm [5/16"] The compact depth of the S34 system creates an ideal solution for closet doors in residential applications. Standard Description Used to pull door open. Standard, included with bi-fold 6.5_ Rod handle ... Return Document
SCREWS General Specification Section 3B & FASTENERS FURNITURE ...
CLOSET LIGHTING SLIDING DOOR HARDWARE VENEERS & DECORATIVE PANELS EDGEBANDING CORBELS & MOLDINGS CABINET - Standard packaging: box of 250 7 7 + % 5HYHDO 7 + % T Door thickness Bore Reveal table Twin overlay 0 7 5 3 1 16 18.5 30 10 8 6 4 19 ... Visit Document
OHIO BOARD OF BUILDING STANDARDS INSPECTION STANDARD
INSPECTION STANDARD TYPE “A” FAMILY DAY-CARE HOME Can all closet door-latching devices be opened by children from the inside of If interior finishes exceeding 1/28 inch in thickness are used in required egress stairways, ... Retrieve Here